All MetalShaping

Go Back   All MetalShaping > Search Forums
  Today's Posts Posts for Last 7 Days Posts for Last 14 Days  

Showing results 1 to 13 of 13
Search took 0.00 seconds.
Search: Posts Made By: Rui
Forum: General Discussion 06-12-2017, 05:05 AM
Replies: 29
Views: 28,609
Posted By Rui
Bringing this up 'cause I followed the same...

Bringing this up 'cause I followed the same procedure. Didnt turn out bad.

https://www.jalopyjournal.com/forum/threads/free-beer.1058643/page-2

Thanks
Forum: General Discussion 05-05-2017, 04:44 AM
Replies: 8
Views: 4,785
Posted By Rui
Thanks for the tip. Never welded such lenght of...

Thanks for the tip. Never welded such lenght of sheet but I'll try to lay short beads at a time and let cool to prevent warping.
Forum: General Discussion 05-05-2017, 04:41 AM
Replies: 8
Views: 4,785
Posted By Rui
Yup, definitely inspiring.

Yup, definitely inspiring.
Forum: General Discussion 05-04-2017, 07:34 AM
Replies: 8
Views: 4,785
Posted By Rui
Thank you for your input and sorry for my lack of...

Thank you for your input and sorry for my lack of feed back.
In fact only now did I came back here to clear some doubts and hadnt noticed your replies.
I have now dissassembled the whole interior,...
Forum: General Discussion 03-23-2017, 04:52 AM
Replies: 8
Views: 4,785
Posted By Rui
Floor patch panel

Guys, hope all is fine.
I've got these rusty floor pans to deal with.
A similar situation i found is described at: http://www.allmetalshaping.com/showthread.php?t=473&highlight=floor+patch
Also...
Forum: Tutorials 03-10-2015, 04:34 AM
Replies: 85
Views: 120,841
Posted By Rui
OK Mark, its a pretty fast and simple task, given...

OK Mark, its a pretty fast and simple task, given you have all the parts. I had a friend milling me those rods so I had to wait a bit, but its pretty much straight forward.
Just dont mess up your...
Forum: Tutorials 03-09-2015, 08:52 AM
Replies: 85
Views: 120,841
Posted By Rui
Here's my shot at it: 1 - 15mmX100 mm rods to...

Here's my shot at it:
1 - 15mmX100 mm rods to be milled
2 - Drilling the 10mm thick plate
3 - Drilled, 3mm apart
4 - Mockup
5 - Welded, plate already cut (hacksaw!)
6 - Mocking up extension to...
Forum: Tutorials 02-24-2015, 04:12 AM
Replies: 85
Views: 120,841
Posted By Rui
Just a (probably dumb) question: Is the bottom...

Just a (probably dumb) question:
Is the bottom end, the one to be welded, of the pins tapered? How else would they tilt to form an even 1/8" gap?
Thanks.
Forum: Tutorials 02-23-2015, 11:36 AM
Replies: 85
Views: 120,841
Posted By Rui
Were is the T dollies getting started thread Mr....

Were is the T dollies getting started thread Mr. Jere? :)
Very good tutorials btw.
Thank you.
Forum: Beginner Projects 02-20-2015, 04:58 AM
Replies: 5
Views: 8,754
Posted By Rui
:) Its just and upgrade from this:...

:)
Its just and upgrade from this: https://www.youtube.com/watch?v=fL26UnAN8zE
Havent finnished it yet.
Regards
Forum: Beginner Projects 02-19-2015, 11:37 AM
Replies: 5
Views: 8,754
Posted By Rui
Thanks for the input and sorry for the late...

Thanks for the input and sorry for the late reply.
The problem(s), I recognize, may lay on my lack of hammerin skills (not every blow hits the exact area I want with the force I want) and also on...
Forum: Beginner Projects 02-18-2015, 06:57 AM
Replies: 5
Views: 8,754
Posted By Rui
First try

Hey there.
This is my first shot so dont laugh!
I gotta say it got me hooked. I'm enjoying each and every strike.
I started with a simple small bowl, as I think everybody does (first two pics)....
Forum: Introductions 01-30-2015, 12:27 PM
Replies: 1
Views: 1,554
Posted By Rui
Hi from Portugal

Hi there. Found this website to be a precious resource, so I decided to register. I'm eager to learn more about metal shaping considering my professional activity (museum - industrial heritage), but...
Showing results 1 to 13 of 13

 
Forum Jump
All times are GMT -5. The time now is 02:25 AM.

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.