#1
|
|||
|
|||
TIG-tacking aluminum - no peek and no filler
This is for those situations where because you are holding one large panel up against another you have only one hand to tack with.
For instance, when adding a formed dash panel onto a cowl section and the weld seam will be 36 to 44 inches long (90cm to 110cm). If you can perform this little skill it will save time you will expend on a clamping fixture. (I showed this on video/dvd back in 1995 - http://www.tinmantech.com/products/d...g-aluminum.php) 01322_n_17akygewna1211 _c.jpg Porsche spyder #030, F2 car, new dash going in - but had to fight to keep alignment while making tack welds. Later on I learned the Better Method from the L.A. car builders - (guys like Phil Remington, Nye Frank, Tom Hanna and others had been doing this since the 1960's) : TIG-tacking - no peek and no filler... Set your TIG machine to AC, 60-70Amps, hi-freq start, gas flow 8. Sharpen a clean 1/8" tung to a 45 deg angle (2% Thor - or Lanth, or Zirc or Pure - any will do just fine ) Withdraw the tung back up in the cup about .050" - 1.2 mm. P1010261 c.jpg Hold the TIG torch smack dab square on the panel joint. This downward pressure is very helpful when forcing two shaped panels into alignment - with the edges touching - the panel edges must touch when tacking as the molten metal will not leap across open space because you want it to ... P1010266 c.jpg Hit the pedal/trigger and wait 3 heart beats. P1010264 c.jpg You have a no-peek fusion/autogenous/no-filler TIG tack. P1010268 c.jpg And as many as you want. P1010269 c.jpg CAVEAT: Solvent clean FIRST with 99% isopropyl .... (WARNING: using chlorinated hydrocarbons such as brake cleaner in the presence of high frequency welding currents will create Phosgene Gas - Mustard Gas and if you breathe this it will give you a hospital visit/stay. This is a nifty time-saving and elegant tack-welding method. Success and joy!
__________________
Kent http://www.tinmantech.com "All it takes is a little practical experience to blow the he!! out of a perfectly good theory." --- Lloyd Rosenquist, charter member AWS, 1919. Last edited by crystallographic; 08-10-2018 at 12:49 PM. |
#2
|
|||
|
|||
That's slick!
__________________
Karl Heinz |
#3
|
|||
|
|||
Thank you
Best regards. Mick
__________________
Michael Henry Sutton |
#4
|
|||
|
|||
Hmmm. I've tried this a number of times with smaller diameter tungstens without much luck. I would be interested to know what difference the 1/8" tungsten makes.
__________________
Tim Freeman |
#5
|
|||
|
|||
Neat technique T Man
Gonna give it a try
__________________
Ed "To Be or To Do" John Boyd |
#6
|
|||
|
|||
Quote:
I have been using acetone for all my cleaning prior to welding is isopropyl a better choice? |
#7
|
|||
|
|||
Quote:
99% Isopropyl is cheaper and just as good for the purpose - and it does not go into your liver within 20 seconds after skin contact. (So I have been told by two separate PhD research chemists, while thanking me for my recommendation ...) Test: Wearing a painter-grade NIOSH respirator (ie: 3M 6200 + 6000 filters) wet a finger with acetone while watching the second timer tick down. When you taste it you have it.
__________________
Kent http://www.tinmantech.com "All it takes is a little practical experience to blow the he!! out of a perfectly good theory." --- Lloyd Rosenquist, charter member AWS, 1919. |
#8
|
|||
|
|||
Thanks for the information really appreciate it
|
#9
|
|||
|
|||
Quote:
__________________
John EK Holden V8 |
#10
|
|||
|
|||
TIG tacking
I can't do the "no peek" thing. I use a clear gas cup. They break easier though if you push on a burr.
__________________
Bill Funk |
Thread Tools | Search this Thread |
Display Modes | |
|
|