Forum: Automotive Projects
09-26-2022, 02:21 AM
|
Replies: 732
Views: 376,367
|
Forum: Introductions
06-12-2022, 04:18 AM
|
Replies: 2
Views: 759
|
Forum: Automotive Projects
06-01-2022, 04:59 PM
|
Replies: 2,271
Views: 4,876,978
|
Forum: Automotive Projects
02-12-2022, 12:15 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
02-12-2022, 11:57 AM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
02-11-2022, 02:43 PM
|
Replies: 2,271
Views: 4,876,978
|
Forum: Automotive Projects
02-11-2022, 02:30 PM
|
Replies: 245
Views: 110,036
The bedside was done by hand and I haven't a...
The bedside was done by hand and I haven't a machine that could shape the panel like I wanted to achieve. The first two mudguard sections had the help from an Eckold for the shrinking. Trying not to...
|
Forum: Automotive Projects
02-11-2022, 03:03 AM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
02-09-2022, 02:31 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
02-09-2022, 02:12 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
02-09-2022, 02:11 PM
|
Replies: 245
Views: 110,036
I think its worth a go to try something that...
I think its worth a go to try something that might not work. Panel steel's cheap, my time is my time and you learn some things. Doing it in separate pieces can open up another can of worms :)
|
Forum: Automotive Projects
02-06-2022, 10:56 AM
|
Replies: 245
Views: 110,036
A paper pattern of the part gives me the flare...
A paper pattern of the part gives me the flare edge. I vivid a line on the inside and that gives me the spot I need to block. With my 100mm pipe, I lay the panel over it and block the line. You've...
|
Forum: Automotive Projects
02-05-2022, 11:29 PM
|
Replies: 245
Views: 110,036
This the start of the LHS bedside. I started by...
This the start of the LHS bedside. I started by plasma cutting some 3mm plate that will become the former for the wheel arch. As I had the RHS to copy, I ran the blank through the rollers until it...
|
Forum: Automotive Projects
02-03-2022, 12:25 AM
|
Replies: 2,271
Views: 4,876,978
|
Forum: Automotive Projects
02-01-2022, 11:02 PM
|
Replies: 732
Views: 376,367
|
Forum: Automotive Projects
12-27-2021, 03:19 AM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
12-27-2021, 03:13 AM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
12-26-2021, 03:39 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
12-26-2021, 03:34 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
12-26-2021, 03:29 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
12-23-2021, 10:14 PM
|
Replies: 245
Views: 110,036
|
Forum: Automotive Projects
12-23-2021, 10:08 PM
|
Replies: 245
Views: 110,036
This is the rear half. Same tools used :cool:....
This is the rear half. Same tools used :cool:. Positioning of the wheel arch took some thought. With the wire buck positioned either on the inside or outside, gave you two different positions.
...
|
Forum: Automotive Projects
12-23-2021, 09:28 PM
|
Replies: 245
Views: 110,036
This is the front section of the mudguard. No...
This is the front section of the mudguard. No action shots. :rolleyes:
Made a rough paper pattern, read the sticky on how to produce a guard with hand tools and then started bashing. Used a stump,...
|
Forum: Automotive Projects
12-23-2021, 09:15 PM
|
Replies: 245
Views: 110,036
This is the first two pieces of the mudguard. I...
This is the first two pieces of the mudguard. I made a die for the nibbler to produce a J swage. This swage makes the mudguard sit tight in against the bedside. I did a few test pieces to determine...
|
Forum: Automotive Projects
12-17-2021, 12:22 PM
|
Replies: 2,271
Views: 4,876,978
Looking good there Marcus. :)
Is there any...
Looking good there Marcus. :)
Is there any anticipation of any drumming going on with the internal steel panels or is there sound deadening to go in. I know it's a bit of an unknown until it's...
|