|
|
|
#1
03-06-2011, 10:53 PM
|
|||
|
|||
New guy from Hayward, CA
Hi I'm Bill and I live in Hayward, CA. I work as a race tech in a vintage race prep shop and am also the shops primary machinist. I do a little sheet metal work there and would love to learn more about it. I've been into cars since I was a teen and currently have a '97 Miata that's my daily/track toy and a '67 International Travelall which is having some restoration and mods done to it (converting it from 2WD to 4X4). I also like photography and study martial arts.
Looking forward to picking people brains and learning a lot...  Here's a pic from work so you all can see what I get to play with... 
__________________
Bill J 
|
|
#2
03-06-2011, 11:12 PM
|
||||
|
||||
|
Bill, welcome to the site and thanks for the introduction. Thanks for the picture of the shop. Hope you find the site helpful.
__________________
Joe Hartson There is more than one way to go to town and they are all correct.
|
|
#3
03-06-2011, 11:29 PM
|
||||
|
||||
|
Welcome aboard
I grew up right off of Harder rd and went to Tennyson high school. My family still lives there.
__________________
Johnny Arial This forum is dedicated to Metal Shaping. Please stay on topic.
|
|
#4
03-07-2011, 12:04 AM
|
||||
|
||||
|
Hello Bill:
Nice shop. Is that a Shadow I see in the top right? I'm in N. CA---Willits. I just recently welded up a 63 Cobra for Campble Auto Restoration. Is that near you?
__________________
Jere Kirkpatrick Valley Forge & Welding HEN-ROB Torch Dealer.  Teaching The Fundamentals of Metal Shaping www.jerekirkpatrick.com All tools are a hammer except the chisel.....That's a screwdriver.
|
|
#5
03-07-2011, 01:50 AM
|
|||
|
|||
|
Hello Bill, I wish I could keep my workshop as clean as that!. I am also interested in photography, don't have much time for it though.
Welcome to the site. David
__________________
Metalshaping DVD. www.metalshapingzone.com Metalshaping with hand tools on youtube http://www.youtube.com/watch?v=IGElSHzm0q8 All things are possible.
|
|
#8
03-07-2011, 12:52 PM
|
|||
|
|||
|
Welcome Bill,
I grew up in Fremont and I'm currently living in San Jose. I'll have to come check out your shop sometime if you guys allow visitors. I have only done very limited machining, but would love to get into it more in the future. It comes in handy to make tools which help in metal shaping. What type of martial arts? I'm a Judo/Jiu Jitsu man myself, but have myself out of shape as if late due to not attending recently. Quote:
__________________
http://www.shawnmarsh.com - My metalshaping portfolio as I get started in the world of metal.
|
|
#9
03-07-2011, 01:13 PM
|
||||
|
||||
|
Shawn:
I just bought a 53 F100 last Friday. It has a Cleveland and C6 in it. What front suspension do you have under the one in your site? I suspect a 9" is under the rear. Is it a 4 link?
__________________
Jere Kirkpatrick Valley Forge & Welding HEN-ROB Torch Dealer. Teaching The Fundamentals of Metal Shaping www.jerekirkpatrick.com All tools are a hammer except the chisel.....That's a screwdriver.
|
|
#10
03-07-2011, 08:52 PM
|
|||
|
|||
|
That particular truck has a Heidt's Mustang 2 front crossmember, and a Jaguar independent rear. The other ones we built at the shop normally consisted of a triangulated 4 link with Currie or Fab9 rear end and Shockwaves all around. I'm not a fan of the Shockwaves but my boss used to sell them like hotcakes so we used them a lot.
My biddy has a 53 with a Monte Carlo front clip, 4 link rear, and bags all around that gets 11" of lift in the front and 14 in the rear and cost less than the Shockwaves. A little more fabrication, but well worth the extra travel IMO.
__________________
http://www.shawnmarsh.com - My metalshaping portfolio as I get started in the world of metal.
|
 |
|
|
Linear Mode
