Forum: Introductions
09-23-2012, 06:14 PM
|
|
Replies: 6
Views: 4,224
|
|
Forum: Introductions
12-22-2011, 07:54 PM
|
|
Replies: 5
Views: 9,418
|
|
Forum: Introductions
09-23-2011, 05:10 PM
|
|
Replies: 8
Views: 11,126
Thanks Ben, but you should set your aim way...
Thanks Ben, but you should set your aim way higher than me! The best think about that truck is that it shows you what you can do with basic tools. The most advanced too I had access to was a harbor...
|
|
Forum: Introductions
09-23-2011, 02:20 PM
|
|
Replies: 8
Views: 11,126
|
|
Forum: Introductions
09-05-2011, 07:23 PM
|
|
Replies: 9
Views: 9,382
|
|
Forum: Introductions
08-13-2011, 01:18 PM
|
|
Replies: 2
Views: 4,075
|
|
Forum: Introductions
05-12-2011, 08:37 AM
|
|
Replies: 3
Views: 7,164
|
|
Forum: Introductions
04-19-2011, 09:15 AM
|
|
Replies: 4
Views: 8,747
|
|
Forum: Introductions
04-12-2011, 09:32 PM
|
|
Replies: 7
Views: 9,093
Question: Do you need to use different gauge...
Question: Do you need to use different gauge metal for any particular reason?
If you do, then you will need to aim the gun more at the thicker piece to concentrate the heat more in the direction,...
|
|
Forum: Introductions
03-16-2011, 08:27 AM
|
|
Replies: 4
Views: 8,137
|
|
Forum: Introductions
03-08-2011, 08:35 PM
|
|
Replies: 12
Views: 14,810
|
|
Forum: Introductions
03-07-2011, 08:52 PM
|
|
Replies: 12
Views: 14,810
That particular truck has a Heidt's Mustang 2...
That particular truck has a Heidt's Mustang 2 front crossmember, and a Jaguar independent rear. The other ones we built at the shop normally consisted of a triangulated 4 link with Currie or Fab9...
|
|
Forum: Introductions
03-07-2011, 12:52 PM
|
|
Replies: 12
Views: 14,810
Welcome Bill,
I grew up in Fremont and I'm...
Welcome Bill,
I grew up in Fremont and I'm currently living in San Jose. I'll have to come check out your shop sometime if you guys allow visitors. I have only done very limited machining, but...
|
|
Forum: Introductions
01-20-2011, 10:16 PM
|
|
Replies: 3
Views: 7,176
|
|
Forum: Introductions
12-20-2010, 10:17 PM
|
|
Replies: 3
Views: 5,432
|
|
Forum: Introductions
12-14-2010, 08:27 PM
|
|
Replies: 14
Views: 18,063
|
|
Forum: Introductions
08-25-2010, 04:57 AM
|
|
Replies: 5
Views: 9,614
|
|
Forum: Introductions
05-05-2010, 08:07 PM
|
|
Replies: 5
Views: 8,700
Welcome, I was looking into signing up at...
Welcome, I was looking into signing up at TechShop, and still may do it, but I have to worry about my job situation first. I am just a few minutes away from you, in Campbell. Maybe sometime I can...
|
|
Forum: Introductions
04-27-2010, 09:39 PM
|
|
Replies: 7
Views: 8,938
Hey Joe,
I am currently working on a 55 Big...
Hey Joe,
I am currently working on a 55 Big Window, doing all the regular stuff. Just did the cab corners this morning in fact. I am doing it for a customer, so I have a lot more time to spend...
|
|
Forum: Introductions
03-16-2010, 10:01 PM
|
|
Replies: 12
Views: 14,360
|
|
Forum: Introductions
03-14-2010, 12:22 AM
|
|
Replies: 3
Views: 7,179
|
|
Forum: Introductions
03-13-2010, 12:14 PM
|
|
Replies: 3
Views: 7,179
Another one from the Bay Area
Hello all. I'm a newbie metalshaper and eager to learn! I went to school for Street Rodding a few years back and got a taste of shaping, and have been working in a Hot Rod shop for about a year. ...
|
